Laserfiche WebLink
7.1.C. - Page 9 2340- 2219R1 <br /> 3.14 FOOTRESTS <br /> 3.14.1 Unit shall be equipped with footrests (pegs) and /or foot boards designed to fold in the event of contact with the <br /> ground. <br /> 3.14.2 Footrests and /or footboards shall be replaceable or provided with replaceable stoppers /skid plates. <br /> 3.15 SIREN / PUBLIC ADDRESS SYSTEM <br /> 3.15.1 Electronic motorcycle (Certified Class "A ", CA Title 13 Compliant) siren /public address (PA) system shall be <br /> provided and installed by supplier prior to delivery. Wail and Yelp modes only. No other tones shall be available <br /> within the box. <br /> 3.15.2 Amplifier and speaker driver shall be rated at >_100 watts. <br /> 3.15.3 PA control system shall be interfaced with an Ericson / GE "Rangr" model S815 radio control head. <br /> 3.15.4 Controls shall be provided to enable operation of siren in Momentary, Wail or Yelp mode. <br /> 3.15.5 Supplier to provide /install relays, pin /socket connectors, and wiring to permit operation as described. <br /> 3.16 MUFFLER (S) <br /> 3.16.1 Muffler(s) shall conform with California Vehicle Code sound restrictions. <br /> 3.16.2 Muffler(s) shall be positioned to provide clearance for utility storage boxes on each side of the rear wheel and the <br /> possible mounting of an electronic siren amplifier under or in front of one of the boxes. <br /> 3.16.3 Unit shall have a maximum of 2 mufflers with a maximum of 4 header pipes into each. <br /> 3.16.4 Muffler(s) shall be of corrosion resistant material. <br /> 3.17 KEYS: Minimum of 2 sets of keys shall be provided for each unit at time of delivery. (For example, a set may include <br /> 1 master and additional keys for specific functions.) <br /> 3.18 COLOR <br /> 3.18.1 Unit shall be painted a combination of manufacturer's gloss black (reference: Ditzler #DQE -9000 or equivalent) <br /> and manufacturer's gloss bright white (reference: Ditzler #DQE8000 or equivalent). <br /> 3.18.2 Paint scheme shall meet agency specified requirements and be compliant with California Code of Regulations <br /> Title 13, Division 2, Chapter 5, Article 5, Section 1141 requirements as exhibited in Attachment 2 on page 12 & <br /> 13. <br /> 3.18.3 Given below are paint scheme requirements for CHP. <br /> a) Frame, if painted, shall be black. <br /> b) Fenders — front — all white (Not including front fender mounting and rear mud guard), rear fender — all white <br /> or all black. <br /> c) For fairing mounted CHP star insignia, the main white panel section shall be large enough to permit <br /> installation of the CHP 5" star insignia without touching border /pinstripe(s). <br /> d) For fairing mounted star insignia, gas tank(s), if visible from exterior, shall be all white. <br /> e) For tank area mounted CHP star insignia, the gas tank(s) shall be black with white side panels contoured to <br /> shape of tank(s) with approximately '/8" black border stripe around the white panel. <br /> f) Panel shall be large enough to permit installation of the CHP 5" star insignia within the white panels without <br /> touching the border stripe. <br /> g) Fairing shall be white with perimeter black border(s) contoured to the shape of the fairing and black pinstripe <br /> shall be used to provide contrast to major panel sections. <br /> h) CHP 5" star insignia referenced above shall be fully visible when viewed from eye level standing to the side <br /> of the unit. <br /> i) Insignia may be placed on the fairing, the gas tank, or the ticket book box depending upon unit configuration. <br /> j) All supplier - installed components shall meet color and quality requirements of factory finish. <br /> k) Paint scheme is subject to approval by purchasing agency. <br /> 3.19 RADIO CONTAINMENT Box (FOR CHP ONLY) <br /> MINTON, W. PAGE 6 OF 13 NOVEMBER 7, 2012 <br /> 1- XX -23 -30 ENFORCEMENT MOTORCYCLE <br />