Laserfiche WebLink
6. 1. C. - Page 9 <br />Bid specifications for Deere 310SJ or similar Wheel Loader Backhoe <br />Compliance <br />es <br />no <br />An anti -theft electronic protection system provided through the monitor shall be a factory <br />option. <br />es <br />no <br />Unit shall have digital display for: engine rpm, engine hours, system voltage, and <br />hydraulic oil temperature. <br />es <br />no <br />The foot throttle shall be suspended <br />es <br />no <br />The machine will have a cab and air conditioner available from the factory. <br />es <br />no <br />The seat shall be suspension vinyl swivel, with fully adjustable armrests and lumbar <br />support. A cloth suspension seat option will be provided at no additional charge. <br />General Specifications <br />es <br />no <br />Vandal protection shall cover the instrument panel. Engine hood, toolbox, hydraulic <br />reservoir, and fuel filler shall be lockable. <br />es <br />no <br />The tilt hood shall have two service positions for easy operation <br />es <br />I no <br />An easy to read periodic maintenance and grease chart shall be posted at eye level <br />prominently displayed on the frame. <br />es <br />no <br />Fuel tank capacity shall be no less than 41 gallons (155 L) and shall be accessible from <br />the ground. <br />es <br />no <br />Operating weight with typical equipment, 1 cu yd (76 cu m) loader bucket and 24 -in x 6.5 <br />cu ft (610 mmx .18 cu m) backhoe bucket standard shall be approximately 16,960 <br />Ib.(7691 kg). Excessive weight causes excess wear on transport and towing vehicles and <br />can cause problems in soft ground conditions. <br />Frames and Structures <br />es <br />no <br />The mainframe shall be a one -piece unitized construction for maximum strength <br />es <br />no <br />Unit shall have four built -in vehicle tiedowns, two in front and two in rear for safe transport <br />between jobs <br />es <br />no <br />The side plate thickness on the loader boom, backhoe boom and mainframe shall be 4.5 <br />mil or greater <br />es <br />no <br />Machine shall be equipped with an exterior mounted, ground level accessed and lockable <br />storage compartment <br />es <br />no <br />Optional, replaceable, bolt -on rubber bumpers will be available to protect the grille frame <br />for severe loading applications <br />Backhoe <br />es <br />no <br />The backhoe with standard dipperstick digging depth shall be at least 14 ft 6 in (4.42 m) <br />es <br />no <br />The lift capacity at ground level with standard dipperstick shall be no less than 3045 lb <br />(1381 kg) <br />es <br />no <br />Maximum SAE dig depth with optional extendable dipperstick extended shall be no less <br />than 18 ft 5 in (5.61 m) <br />es <br />no <br />The lift capacity at full height with standard dipperstick shall be no less than 3745 lb (1699 <br />kg) <br />es <br />no <br />The swing lock pin shall be stored in the operator's station <br />es <br />no <br />The stabilizer valve will be two directional, anti -drift <br />es <br />no <br />The stabilizer shall have reversible pads <br />es <br />no <br />Optional extendible dipperstick shall extend no less than 3 ft 6 in (1.07 m) <br />es <br />no <br />The Backhoe boom design shall be a power curve for loading into the center of the <br />truckbed. <br />es <br />no <br />The backhoe boom shall be an hourglass shape for maximum strength and optimized <br />visibility to the work tool. <br />sJ <br />no <br />Digging force with standard backhoe, bucket cylinder shall be at least 11,990 lb (53.3 kN) <br />8/9/2011 and 3:51 PM <br />Page 3 of 4 <br />