Agmt12 MetalCraft Marine Inc. - Laserfiche WebLink

Browse Search

3.0.22 The Contractor shall design and construct the vessel such that the hull shape, the location of all hull openings and location of transducers and all other appendages satisfy the design recommendations and requirements of the engine manufacturer. 3.0.23 There shall be two (2) hose cabinets/lockers in the aft section of the deck on each side measuring 72'X 12"X 48" interior dimensions. The compartment will be divided into two sections. The top compartment shall have a door opening on top running the length of the compartment with the hinges on the outside section. There will be a floor separating the top compartment from the bottom at 24 inches. The bottom compartment shall have a side door facing the interior running the length of the compartment with the hinge on the bottom. A channel or gutter shall be installed to collect water seepage through the hatches and drain it clear of the hatch opening. All latches to be mounted so not to be a trip hazard. 3.0.24 The deck shall have a four (4) cleat configuration. 3.0.25 A 4-inch diameter half-round rubber fender shall be fitted around the entire deck edge at the sheer line. The rubber fender shall be provided with means of preventing separation of the fender at joints between fender sections. 3.0.26 Four (4) 3-inch mooring bits (two at the bow and one at each stern quarter) shall be welded to the deck and two open bow chocks shall be welded to the deck. 3.0.27 Four (4) 12-inch cleats shall be provided, one each, port and starboard, at the forward end of the cabin/pilothouse and one each, port and starboard, at the aft end of the cabin/pilothouse. 3.0.28 A minimum of four (6) 10-pound zinc anodes shall be placed below the waterline at the transom. Doublers plates or insert plates shall be fitted in way of the zinc anodes. 3.0.29 All structure shall be free from resonant vibration over the boat's speed range. Free from resonant vibration means free from vibration detrimental to the fatigue life of the hull structure,the operation of inechanical or electrical equipment and systems installed in the boat, or to the health and safety of personnel operating the boat. 3.0.30 It is required that the vessel be provided with a single level main deck free from obstructions. Side decks shall be a minimum of 18" in width for crew safety. Safety railings shall be mounted around the full perimeter of the aft cockpit deck. The forede�k railings - shall be mounted inboard both sides of the cabin roof and around the cuddy roof and port and starboard of the foredeck. Safety rails shall be accessible from any point on deck for a crewman. 3.1 Cabin/Pilothouse Structure: 3.11 The cabin/pilothouse shall be a minimum of eight(8) feet long and have clear headroom of six (6) feet, six (6) inches. The cabin width shall allow a walkway around the cabin that is at least 22 inches wide, port and starboard. 3.1.2 The cabin/pilothouse shall be acoustically and thermally insulated. Engine noise level in the cabin/pilothouse at full power shall be no greater than 85db at the steering station, underway, at maximum rated continuous power, not pumping water, with cabin/pilothouse doors, windows and hatches closed, and not greater than 90db under the same conditions when pumping water. 3.1.3 Front windows shall be fitted with window washers and self-parking wipers. 3.1.4 Front windows shall have a 10 to 15-degree slope from the vertical. Front windshields shall be heated glass. Windows shall slope outwards from bottom to top. Side and aft windows shall have a 15% tint, forward windshields shall be clear. Cabin windows shall be constructed in such a way to give a 360 degree view. 3.1.5 Forward Side windows shall open by sliding and have a provision to be locked closed. 3.1.6 N/A 3.1.7 All glazing shall be 1/4" safety glass, following the standards and recommendations of the ABYC. 7